hours left for
same day shipping
hours left for
same day shipping

Installing a Landscape Lighting System: A Step-by-Step Guide



Installing a Landscape Lighting System: A Step-by-Step Guide  

Edited: 05/16/2024


Low-voltage landscape lighting is a surefire method to sharpen curb appeal and add a degree of safety and security. While planning an outdoor lighting system affords you the opportunity to explore the most uncharted, imaginative corners of your creativity, installing a landscape lighting system lets you showcase it all on your natural canvas.


Prepare to give your wildest landscape lighting ambitions a pulse with this easy and detailed step-by-step guide.

DIY Landscape Lighting Installation 

Fashioned along walkways, steps, driveways, or directed up at trees, walls, and fences, a low-voltage lighting system typically requires three elements: a transformer, fixtures, and low-voltage electrical wire. You don’t have to be comfortable or have experience with wiring to install this type of system.


Because the typical landscape lighting system operates on only 12 volts of electricity, it’s completely safe for do-it-yourself installation. Digging shallow trenches for the low-voltage cable might result in some sweat, but installing and adjusting the light fixtures is a mere stone’s throw from effortless. 

Tools You’ll Need for Landscape Lighting Installation 

Lighting Warehouse is armed with a wealth of lamps, fixtures, and transformers to make your home the toast of the block, but to get it done—and get it done right—you’ll need a few helpers.

  • Wire stripper—Make sure to find a solid, durable wire stripper as you’ll be using this often when installing lighting. You can even find some that automatically gauge wire diameter so you’ll never need to worry about stripping any interior wire from the bundle.
  • Wire and edging trencher—This specialized, flat shovel allows you to dig shallow trenches for wiring (about 6” to 8” deep). Using a trencher will not only speed along the installation process but also make the process easier as you won’t be exerting energy digging any deeper than needed.
  • Wire connectors—Though a vast majority of lighting warehouse products come pre-packaged with wire connectors, it’s good practice to keep extra on-hand.
  • Crimp tool—These are used to combine the individual wires you’ve exposed during stripping so the connection can solidify and adequate electrical current can navigate through the fixture(s).
  • 6-in-1 screwdriver—Using a screwdriver with multi-use tops that fit all the standard screw variations can reduce the number of trips back and forth to your shed or toolbox.
  • Power drill—Though not mandatory, using a power drill to mount fixtures to a surface can expedite the process, adding time to your day while subtracting stress from your installation experience.
  • Marking flags—Using obvious indicators to identify existing cable or irrigation lines prevents wasted time and money.

How to Install a Landscape Lighting System 

Step 1: Assemble the Fixtures 

Unpack and remove everything from the box, installing bulbs in any lamp-ready fixtures. Next, attach mounts to fixtures using any of the three mounting procedures.

  1. Stake mounting: stake attaches to the fixture before placed directly into the ground
  2. Surface mounting: fixture attaches to a hard surface, normally with a power drill
  3. In-ground mounting: fixture mounts directly into the earth  

Step 2: Mark Cable and Irrigation Lines 

Use marking flags to indicate existing irrigation or wires so they aren’t compromised during the installation process.

Step 3: Mount the Transformer 

When choosing your transformer’s location, it’s imperative to bear in mind a few things:

  1. It must have one foot of clearance in every direction.
  2. It must be at least 30 feet away from water features.
  3. It must be on a surface that can survive the heat it produces. 

Step 4: Position Fixtures and Wiring 

Clear a path for your wire runs and place your fixtures based on the project map from your planning  Stage. Remember to space path lights about 8 to 10 feet apart, with the first fixture positioned at least 10 feet from the transformer. Once the fixtures are set, lay the low-voltage wire along the line of light fixtures. If you encounter an obstacle, such as a fence or a shrub, string the wire under or around it. 

Step 5: Dig Trenches/Turn over the Sod 

Move the light fixtures out of the way then take your edging trencher and sliding underneath the top layer of grass. If setting path lights, you’ll want to place the trencher about a foot in from the edge of the walkway. Next, lift up on the handle to separate the grass from the soil then fold over this scalped portion of sod, continuing the process along the entirety of the walkway. Using the corner of the shovel’s blade, scratch a 6-inch-deep trench in the soil where the wire will be placed.

Pro-Tip: If necessary, set the light fixtures on top of the folded sod to prevent it from flopping back Down. 

Step 6: Bury the Wire 

  • Set the low-voltage electrical wire in the trench. Leave about 5 inches of excess wire at each fixture point for connections and potential adjustments.
  • Smooth the soil over the trench, leaving the wire sticking up out of the soil near each fixture. 
  • Cut a slit in the detached sod where the fixture will sit and fold the sod back over the soil, keeping the cable for each fixture above the grass.  

Pro-Tip: Be sure not to bury the wire below 6 inches or you’ll have difficulty connecting the light fixture.

Step 7: Connect Transformer to Main Wire Runs 

First, run the cable up to your outdoor electrical outlet. Next, use wire strippers to cut the cable and strip off ½ inch of the rubber insulation. After that, slide the stripped wires under the two terminal screws that should be located on the bottom of the transformer before tightening the screws completely to secure the cable in place. Once you’ve confirmed the cable is confidently in position, drive a wood stake into the ground next to the outlet then screw the transformer to the stake. You can also mount the transformer directly to the wall of the house. After you’ve verified the transformer is mounted, plug in the transformer.

Step 8: Connect Fixtures to Main Wire Runs 

Connecting fixtures to your main runs can be easily accomplished by two splicing methods: twist-on and clamping. The former, twist-on, is the most common method for fixture connections. These connections are done by stripping the last half inch of wire at each end then twisting them together in a clockwise direction. Once twisted, simply insert the connection into the cap and twist clockwise until the wire begins to spin in tandem with the cap. 

Clamping, on the other hand, involves clamp connect junctions. Simply invert the stripped wire ends into the terminal, push down the lever, and close the housing to safeguard the connection from moisture and corrosion.

If you’re dealing with a bundle of fixtures, consider using a hub. A hub offers easy connection for multiple fixtures in a single location and can either be buried underground or stake-mounted.

Step 9: Test and Adjust 

Once your connections are complete, it’s time to test your system. Power on your transformer then scour your property for any inconsistencies or system failures. We recommend performing this task at night to get the full lighting effect. If one or more lights is out, which isn’t unusual, you may have a bad connection. In the event this happens, feel free to contact the pros at Lighting Warehouse for assistance to get the glow. Don’t procrastinate this step as a burned-out bulb that isn’t promptly replaced with shorten the life of the other bulbs.

If every fixture is beaming to your satisfaction, manipulate the lighting directions according to your predetermined design. Be sure to keep an eye out for glare bouncing off your fixtures. To remedy glare overload, simply adjust the angle of the fixture or its glare-reducing shroud.

Step 10: Bury Remaining Wire and Program Timer

Once the lights are in iron-smooth operation and positioned in step with your landscape lighting vision, bury the excess wire 6 inches below the sod then level the sod surrounding the fixtures. If necessary, use a shovel to cut the sod around the fixtures. After the sod is firmly pressed and/or carved out, use a garden hose to soak the area with water. Lastly, customize your transformer timer to correspond with your schedule so that the correct lights shine at the correct times.


Congratulations on successfully installing your very own landscape lighting system. If your installation journey didn’t pan out as you hoped because a few hiccups or a faulty part, give yourself credit for the attempt. We realize that, while installing an entire landscape lighting system is doable, it’s not a one-size-fits-all ordeal. For questions or assistance of any kind, please don’t hesitate to contact our expert, above-and-beyond customer service team for extra guidance.

Landscape Lighting Installation FAQs

How long does it take to install landscape lights? 

Expect to spend 8 to 10 hours installing an average-size landscape lighting system, though factors such 
as property size, fixture quantity, and terrain can shorten or extend the installation process. 

Can I use an extension cord to install outdoor lights? 

Never use an extension cord or indoor outlet when installing landscape lights. If your home doesn’t 
contain a GFCI protected outdoor electrical outlet nearby, it’s advantageous to hire a licensed electrician to install one before performing any DIY landscape lighting installation.

Can you bury wire without a conduit? 

In accordance with National Electric Code (NEC) guidelines, direct burial wire is approved to be run in the earth without the use of a conduit to surround it. The thickness and material of the wire’s insulation protects the wire from moisture and other harmful influences.